How to make a solar garden flower light from recycled PET bottles – take two

IMGP7921

Solar flower light emits a soft glow through the PET flowers at night

IMGP7673

Pretty and chirpy during the day in the sun

Well, so many people have been searching my site for the real “how to” instructions for making a flower out of PET bottles, and my last post didn’t really do full justice to the process, so I have made amends below.  This is attempt number two.  For attempt number one (fluro light cover) see here.

Attempt number two is a solar flower light that I have hanging in the garden.IMGP7675

Wash PET bottles

Cut in half with stanley knife – I found it easy to just make a small cut with the knife then cut the rest with scissors

IMGP7625Cut both the tops and the bottom halves into strips with scissors

Fold the petals back and kind of crunch them up so that they look like IMGP7630flowers

keep any small snipped out bits for the centre of the flowers

spray paint everything in a few coloursIMGP7619

IMGP7622poke a couple of holes in the bottom of each of your new flowers to thread wire through

poke holes in the centre bits also – I used a soldering iron for thisIMGP7621

IMGP7672thread wire through the flowers, attaching a centre bit or stamen as needed

use the wire to attach to an old piece of chicken wire or fly screen

IMGP7628once you have all the flowers attached to the fly screen, make into  circle and secureIMGP7669

then use wire and hang some flowers artistically from the bottom

use curtain ring to make a hanger for the light

I used a small solar bulb made by Nokero (short for No Kerosene) and used another curtain ring to hang it inside the middle of the light

If I had access to solar fairy lights here in Fiji, that would be my first preference.IMGP7679

it really looks beautiful at night, and because I used bright colours, it is also pretty during the day

it took me a morning to figure it out but I am glad I did it.  It is one small step to making some use of the bottles that are everywhere here in Fiji, and IMGP7683a small step to getting them out of the environment!  The thing is, PET bottles can be recycled, but you have to actually send them to recycling for that to work.

As Mother Teresa once said, “to keep a lamp burning, you have to put oil in it”

IMGP7666IMGP7667TIP FOR NEW PLAYERS:  I did think it would look pretty with some fairy lights hanging in it, but even though the fairy lights have the wires insulated, when I turned it on, it did look beautiful, but as I made the frame out of metal fly wire, when I touched it, it gave me a shock, so then I went to the solar version.

How to make a light of flowers from recycled PET plastic bottles

 

IMGP7607

Light cover made from recycled PET plastic bottles

Once again, I decided I had better stop talking, and start doing.  We have collected so many bottles at our place as we investigate options for recycling the 44 million PET bottles that are sold in Fiji each year. On the weekend, we made a cover for the outdoor fluorescent light out of recycled PET plastic bottles.

I had seen something similar on the internet, and decided to give it a try, as often these crafty ideas are not as easy as they appear, but this one was!

Here is what we did:

IMGP7603

Fixture attached to ceiling

My friend Vuli came for a visit with two of her grandkids.  It was her and I, plus 4 little boys as “helpers”, plus I had two boys with me.  I was going to take photos of the process, but we got caught up trying to mind 4 boys with a soldering iron and stanley knives, so you get the picture.

I can make an instructional set of pictures if anyone is interested.  The whole thing took about 2 hours in between making snacks for the kids and being a gopher for my husband while he and his father were doing some yard work, and Vuli and I secretly believe that we would have done it faster, and with a bit more of a polished result had we been “alone”.  It was so fun though and the kids had a ball, plus do they really want long lectures on recycling, or just a taste of the action?

Materials:

1 piece of chicken wire or other mesh as big as you need to hang below your fluorescent light (ours was about 25cm by 85cm)

  • 12 or 14 plastic PET bottles any size
  • scissors
  • stanley knifeIMGP7610
  • spray paint
  • old wire (we used an old piece of electrical wire and pulled it apart)
  • a couple of curtain rings if you are fancy
  • a couple of screw in eyelets if you want to permanently attach it
  • soldering iron or other hot poker type device to poke holes in the flowers to thread the wire through

Method

  1. wash the bottles
  2. cut the bottles in half around the middle.  We used the stanley knife just to make the first incision, and then used the scissors to cut around
  3. use the scissors and cut lots of little strips into the bottles to form the petals

    IMGP7608

    With the light on

  4. you can use a butter knife and pull the strips similar to the way you use curling ribbon, but we found the simplest thing for the kids was just to bend the petals back and kind of fold them for some kinks
  5. you can put two pieces one inside the other if you want a fuller flower, or just use one
  6. put on newspaper or an old mat and use any colours of spray paint to lightly spray each flower (we had black, gold and red)
  7. use the soldering iron or a heated up skewer to poke a hole in the base of each flower
  8. thread a piece of wire through the hole (or fishing line might be good)
  9. attach the wire to the chicken wire frame
  10. use one longer piece of wire at each end to make it hang, and put curtain ring on each so that you can hang up
  11. use two screw islets to hang from ceiling, or we just threaded some wire through the verandah.
  12. anyway, it looks really nice, and even the men like it.  It gives the fluro light a softer glow somehow

 

IMGP7609

Daytime view with light off